Cisco 40-Gigabit and 100-Gigabit CFP
Transceiver Modules Installation Note
Revised: July 5, 2012
Product Numbers:
CFP-100G-LR4
CFP-40G-SR4
CFP-40G-FR
CFP-40G-LR4
CVR-CPR-4SFP10G
CFP-100G-SR10
The CFP transceiver module connects the electrical circuitry of the platform with an optical network.
This installation note provides instructions for installing the 40-Gigabit and 100-Gigabit CFP transceiver
modules.
Contents
This document contains these sections:
•
•
•
•
•
•
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Overview
Figure 2
CFP-40G-SR4 Transceiver Features
1
2
Captive installation screws
Optical bore dust plug
3
Transmit and receive multifiber optical bore,
MPO/MTP connector
Figure 3 shows a CVR-CFP-4SFP10G module. This is an adapter module that converts a Cisco switch
or router CFP port to four 10-Gigabit SFP+ ports. The SFP+ transceivers are not included with the
converter module.
Figure 3
CVR-CFP-4SFP10G CFP to Four SFP+ Converter Module
1
Captive installation screws
2
10G SFP+ ports (4X)
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
3
Overview
Table 1 lists the currently supported types of CFP transceivers.
Table 1 CFP Transceiver Product Numbers and Descriptions
CFP Transceiver Module Transceiver Description
Product Number
100-Gigabit
CFP-100G-LR4
Cisco 100GBASE-LR4 CFP transceiver module for SMF, 1310 nm
window, SC connector
CFP-100G-SR10
Cisco 100GBASE-SR10 CFP transceiver module for MMF, 850 nm,
24-fiber MPO/MTP connector
40-Gigabit
CFP-40G-SR4
Cisco 40GBASE-SR4 CFP transceiver module forMMF, 850 nm,
12-fiber MPO/MTP connector
CFP-40G-LR4
Cisco multirate 40GBASE-LR4 and OTU3 C4S1-2D1 for SMF,
1310 nm window, SC connector
CFP-40G-FR
Cisco multirate 40GBASE-FR and OTU3 VSR2000-3R2 CFP
transceiver module for SMF, 1550 nm, SC connector
CVR-CFP-4SFP10G
Cisco FourX CFP to four SFP+ Converter Module
Note
The SC and MPO connectors on the optical CFP transceivers support network interface cables with
either Physical Contact (PC) or Ultra-Physical Contact (UPC) flat polished face types. The SC and MPO
connectors on the optical CFP transceivers do not support network interface cables with an Angle
Polished Connector (APC) polished face type.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
4
Overview
Table 2 lists the 100-Gigabit CFP port cabling specifications. Table 3 lists the optical transmit and
receive specifications for 100-Gigabit CFP transceivers.
Table 2
CFP Optical Transceiver Module Cabling Specifications
CFP Transceiver
Note
The minimum cabling distance for the CFP-100G-LR4, CFP-40G-FR, and the CFP-40G-LR4
transceivers is 6.56 feet (2 meters). The minimum cabling distance for the CFP-40G-SR4 and the
CFP-100G-SR10 transceivers is 1.64 feet (0.5 m).
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
5
Safety
Table 3
CFP Transceiver Module Optical Transmit and Receive Specifications
CFP Transceiver
Module Model
Transceiver Type
Transmit
Power (dBm)
Receive Power Transmit and Receive
(dBm)
Wavelength (nm)
Four lanes:
1271
CFP-40G-LR4
40GBASE-LR4,
1310-nm SMF
2.3 per lane
(Max)
2.3 per lane
(Max)
–7 per lane
(Min)
–13.7 per lane 1291
(Min)
1311
1331
OTU3 C4S1-2D1, 2.3 per lane
2.3 per lane
(Max)
Four lanes:
1310-nm SMF
(Max)
1271
1291
1311
1331
–2.3 per lane
(Min)
–9 per lane
(Min)
CFP-40G-FR
40GBASE-FR and 3.0 (Max)
3.0 (Max)
-6.0 (Min)
One lane, 1530 to
1565
OTU3
0.0 (Min)
VSR2000-3R2,
1550 nm SMF
Safety
Safety warnings appear throughout this publication in procedures that may harm you if performed
incorrectly or are ignored. A warning symbol precedes each warning statement.
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
6
Safety
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
WICHTIGE SICHERHEITSHINWEISE
Warnung
Avvertenza
Advarsel
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
7
Safety
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
VIKTIGA SÄKERHETSANVISNINGAR
Varning!
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
8
Safety
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
9
Safety
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
10
Safety
Warning
Warning
Class 1 laser product. Statement 1008
Because invisible laser radiation may be emitted from the aperture of the port when no cable is
connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
11
Required Tools
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
Use of controls, adjustments, or performing procedures other than those specified may result in
hazardous radiation exposure. Statement 1057
Required Tools
You will need these tools to install the CFP transceiver module:
•
•
Small flat-blade screwdriver for removing the CFP transceiver socket cover.
Wrist strap or other personal grounding device to prevent electro-static discharge (ESD)
occurrences.
•
Fiber-optic end-face cleaning tools and inspection equipment. For complete information on
inspecting and cleaning fiber-optic connections, refer to the white paper at this URL:
Installing the CFP Transceiver
Caution
The CFP transceiver is a static-sensitive device. Always use an ESD wrist strap or similar individual
grounding device when handling the CFP transceivers or coming into contact with the modules.
To install a CFP transceiver, follow these steps:
Step 1
Step 2
Step 3
Step 4
Remove the CFP transceiver from its protective packaging.
Check the label on the CFP transceiver body to verify that you have the correct model for your network.
Remove the dust plug from the CFP transceiver module optical port and set it aside.
Align the CFP device into the transceiver port socket of your networking module, and slide it in until the
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
12
Installing the CFP Transceiver
Step 5
Press firmly on the front of the CFP transceiver with your thumb to fully seat it in the transceiver socket.
Figure 5
Seating the CFP Transceiver Module in the Socket
Step 6
Gently tighten the two captive installation screws on the transceiver to secure the CFP transceiver in the
Figure 6
Securing the CFP Transceiver Module
LINK
Step 7
Reinstall the dust plug into the CFP transceiver’s optical bore until you are ready to attach the network
interface cable.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
14
Installing the CFP Transceiver
Step 8
When you are ready to attach the network cable interface, remove the dust plugs and inspect and clean
fiber connector end faces, and then immediately attach the network interface cable connectors into the
Note
install 10GBASE-X SFP+ transceivers in the adapter ports. Follow the SFP+ transceiver
installation procedure documented at:
For complete information on inspecting and cleaning fiber-optic connections, see the white-paper
document at this URL:
Figure 7
Cabling an Optical CFP Transceiver Module with SC Connectors
1
SC connector
L
I
NK
2
Network interface
cable
A
C
TI
VE
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
15
Removing the CFP Transceiver
Figure 8
Cabling an Optical CFP Transceiver Module with MPO Connectors
1
2
LINK
Network interface
LINK
cable
A
CTIVE
Removing the CFP Transceiver
Caution
The CFP transceiver is a static-sensitive device. Always use an ESD wrist strap or similar individual
grounding device when handling the CFP transceivers or coming into contact with the modules.
Warning
Warning
Class 1 laser product. Statement 1008
Because invisible laser radiation may be emitted from the aperture of the port when no cable is
connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
16
Removing the CFP Transceiver
If you need to remove a CFP transceiver, follow these steps:
Step 1
Disconnect the network fiber-optic cable from the CFP transceiver connectors. Immediately reinstall the
dust plugs in the CFP transceiver optical bores.
Step 2
Step 3
Loosen the two captive installation screws that secure the CFP to the networking module.
transceiver in antistatic protective packaging.
Figure 9
Removing a CFP Transceiver Module
Captive installation
screws
NK
I
L
Optical bore
dust plugs
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
17
Translated Safety Warnings
Translated Safety Warnings
This section repeats in multiple languages the basic warnings that appear in this document.
Statement 70—Invisible Laser Radiation Warning
Warning
Because invisible laser radiation may be emitted from the aperture of the port when no cable is
connected, avoid exposure to laser radiation and do not stare into open apertures.
Waarschuwing
Omdat er onzichtbare laserstraling uit de opening van de poort geëmitteerd kan worden wanneer er
geen kabel aangesloten is, dient men om blootstelling aan laserstraling te vermijden niet in de open
openingen te kijken.
Varoitus
Kun porttiin ei ole kytketty kaapelia, portin aukosta voi vuotaa näkymätöntä lasersäteilyä. Älä katso
avoimiin aukkoihin, jotta et altistu säteilylle.
Attention
Etant donné qu’un rayonnement laser invisible peut être émis par l’ouverture du port quand aucun
câble n’est connecté, ne pas regarder dans les ouvertures béantes afin d’éviter tout risque
d’exposition au rayonnement laser.
Warnung
Aus der Öffnung des Ports kann unsichtbare Laserstrahlung austreten, wenn kein Kabel
angeschlossen ist. Kontakt mit Laserstrahlung vermeiden und nicht in offene Öffnungen blicken.
Avvertenza
Poiché quando nessun cavo è collegato alla porta, da quest’ultima potrebbe essere emessa
radiazione laser invisibile, evitare l’esposizione a tale radiazione e non fissare con gli occhi porte
a cui non siano collegati cavi.
Advarsel
Aviso
Usynlige laserstråler kan sendes ut fra åpningen på utgangen når ingen kabel er tilkoblet. Unngå
utsettelse for laserstråling og se ikke inn i åpninger som ikke er tildekket.
Evite uma exposição à radiação laser e não olhe através de aberturas expostas, porque poderá
ocorrer emissão de radiação laser invisível a partir da abertura da porta, quando não estiver
qualquer cabo conectado.
¡Advertencia!
Varning!
Cuando no esté conectado ningún cable, pueden emitirse radiaciones láser invisibles por el orificio
del puerto. Evitar la exposición a radiaciones láser y no mirar fijamente los orificios abiertos.
Osynliga laserstrålar kan sändas ut från öppningen i porten när ingen kabel är ansluten. Undvik
exponering för laserstrålning och titta inte in i ej täckta öppningar.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
18
Translated Safety Warnings
Statement 1008—Class 1 Laser Product
Warning
Class 1 laser product.
Waarschuwing
Varoitus
Klasse-1 laser produkt.
Luokan 1 lasertuote.
Attention
Warnung
Avvertenza
Advarsel
Produit laser de classe 1.
Laserprodukt der Klasse 1.
Prodotto laser di Classe 1.
Laserprodukt av klasse 1.
Produto laser de classe 1.
Producto láser Clase I.
Laserprodukt av klass 1.
Aviso
¡Advertencia!
Varning!
Aviso
Produto a laser de classe 1.
Klasse 1 laserprodukt.
Advarsel
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
19
Translated Safety Warnings
Statement 1040—Product Disposal
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Waarschuwing
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
Varoitus
Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives
de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
Avvertenza
Advarsel
Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og
bestemmelser.
Aviso
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
20
Translated Safety Warnings
Varning!
Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.
Aviso
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações
nacionais.
Advarsel
Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
21
Translated Safety Warnings
Statement 1057—Hazardous Radiation Exposure
Warning
Waarschuwing
Varoitus
Use of controls, adjustments, or performing procedures other than those specified may result in
hazardous radiation exposure.
Het gebruik van regelaars of bijstellingen of het uitvoeren van procedures anders dan opgegeven
kan leiden tot blootstelling aan gevaarlijke straling.
Säätimien tai säätöjen käyttö ja toimenpiteiden suorittaminen ohjeista poikkeavalla tavalla voi
altistaa vaaralliselle säteilylle.
Attention
L’utilisation de commandes, de réglages ou de procédures autres que ceux spécifiés peut entraîner
une exposition dangereuse à des radiations.
Warnung
Die Verwendung von nicht spezifizierten Steuerelementen, Einstellungen oder Verfahrensweisen
kann eine gefährliche Strahlenexposition zur Folge haben.
Avvertenza
Advarsel
L’adozione di controlli, regolazioni o procedure diverse da quelle specificate può comportare il
pericolo di esposizione a radiazioni.
Bruk av kontroller eller justeringer eller utførelse av prosedyrer som ikke er spesifiserte, kan
resultere i farlig strålingseksponering.
Aviso
O uso de controles, ajustes ou desempenho de procedimentos diferentes dos especificados pode
resultar em exposição prejudicial de radiação.
¡Advertencia!
Varning!
La aplicación de controles, ajustes y procedimientos distintos a los especificados puede comportar
una exposición peligrosa a la radiación.
Om andra kontroller eller justeringar än de angivna används, eller om andra processer än de
angivna genomförs, kan skadlig strålning avges.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
22
Translated Safety Warnings
Aviso
O uso de controles, ajustes ou procedimentos diferentes daqueles especificados pode resultar em
exposição perigosa à radiação.
Advarsel
Brug af kontrolfunktioner, justeringer, eller udførelse af procedurer andre end de, der er angivet, kan
resultere i udsættelse for farlig bestråling.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
23
Obtaining Documentation and Submitting a Service Request
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the publications documents that support your specific Cisco device.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any
examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.
Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2010–2012 Cisco Systems, Inc. All rights reserved.
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
24
|
Black Box Stereo Amplifier 1 In 12 Out Audio Video Baseband Amplifier User Manual
Black Box Switch CATx User Manual
Black Decker Juicer CJ500 User Manual
Bogen Car Speaker HS30EZ User Manual
Brainboxes Network Card BL 554 User Manual
Brother Printer DCP L2540DW User Manual
Carrier Fan 13 50XP User Manual
Casio Watch ANA3H3E 1 User Manual
Cisco Systems Conference Phone 52 User Manual
Cisco Systems IP Phone 7915 User Manual