Extinguishing the stove
OPERATING INSTRUCTIONS
Using the stove
Preheating the stove
2. After fuel has been primed to the stove, ignite the fuel through the ignition port with a
lighter or a match to preheat the generator pipe.
- Before using the Brunton Bantam stove, please read and follow all the steps
below carefully.
1. To extinguish the stove, turn the valve knob to the OFF position and flip the bottle over.
NOTE: The stove will continue to burn for a short time until all of the fuel in the generator tube
- Before using the stove with white gas, it is necessary to pre-heat the fuel. This is called
priming the stove.
1. Unfold the stove legs and place the stove on a flat surface.
3. After pre-heating (1-2minutes) slowly open the valve to allow fuel to flow through the
generator unit. The flame may appear yellow for the first minute of operation but should
settle to a crisp blue flame that is the normal cooking flame. If an excessively high yellow
flame is evident, turn off the stove and repeat the preheating process.
4. Never allow fuel to overflow from the stove base, as leaking fuel will ignite and may
cause a fire hazard and serious injury.
and fuel hose is consumed.
TM
Flip
1. Turn the valve knob counter clockwise to the (ON) position and wait 1-2 seconds until the
jet emits a small amount of fuel onto the priming pad then close the valve by rotating the knob
counter clockwise to the (OFF) Position. If fuel does not flow, the fuel bottle is low on
gas and the bottle may need preasurizing or more fuel.
BANTAM
Filling the fuel bottle
1. Pour the fuel up to the fill line on the bottle. Do not overfill.
2. Insert pump and turn clockwise to tighten.
5. If the flame decreases in intensity, further pressurization of the fuel bottle is required.
Instructions for 81-100726
Small flame remains for 2-3
minutes consuming all the fuel in
the hose.
fill line
2. After the fire extinguishes, the stove will remain hot, wait until the stove cools down.
3. Separate the stove from pump.
4. Fuel bottle and pump can be transported as a connected assembly. When separating the
1-2 seconds
pump from fuel bottle, turn the pump slowly so that the pressure retained inside the fuel
y
3. Before pumping pressure into the fuel
bottle, ensure that the control valve for the
stove unit is set to the OFF position. Pump
the handle on the pump set to pressurize
the fuel bottle (20 strokes).
.
bottle can release gradually
2. After connecting the flexible hose to
the pump, ensure that the fuel bottle is
placed on a flat surface.
Manual ignition
20-30 times
Hissing
Turn slowly counter-
clockwise after preheating
NOTE: Less fuel in the bottle needs more
pumping strokes to pressurize the bottle.
WARNING
Use outdoors only and do not allow children to reach
Using the stove on uneven surface is very dangerous and may cause a fire hazard
and serious injury.
Please read, understand and follow all instructions and warnings before using this
product. The proper fuel bottle for this product is included.
WARNING
WARNING
To avoid the possibility of serious injury, use only a Brunton pump and bottle.
Use only White Gasoline, other fuel could clog the nozzle and may cause a fire hazard.
Keep away from children.
When the fuel bottle has been connected to the pump be sure that the valve knob is set
to the OFF position.
Inner pressure exclusion
Separation
Before igniting the stove, ensure that the valve knob is turned to
the clockwise (OFF) position.
Preheating
Working
When the stove is in use, keep fuel bottle as far away as possible.
Never place your head or body above the stove when lighting it.
Stove parts
WARRANTY
PARTS REPLACEMENT AND MAINTENANCE
Poor performance & nozzle clogging
Brunton warrants this product to be free of defects in workmanship and materials for the
lifetime of the original owner, and is nontransferable. If you have any problems with your
Brunton stove, the stove should be returned to the dealer or sent to Brunton, 2255
Brunton Court, Riverton, WY 82501 U.S.A. Please contact Brunton at the number below
to obtain RA#. Clean food and soot from stove before shipping. Shipping cost to Brunton
is the responsibility of the purchaser. Return postage will be paid by Brunton. Please
return this warranty card to Brunton as a proof of purchase. This warranty does not cover
damage caused by accident, misuse, abuse, or tampering. A nominal charge will be
assessed to repair such damage.
- Colgging inside the nozzle or generator tube may disturb the fuel and create poor stove
performance.
- Remove clogging inside the nozzle hole with a nozzle pin.
- If clogging persists inside of the nozzle or generator tube, a more thorough cleaning
is required.
Checking & replacing seals and 0-rings
head
leg pin
Dried or torn parts need to be replaced. Check the color and size and any printed
markings and contact your nearest Brunton stock list or retailer for replacements.
(Oil seals, Oil, Nozzle, Tool kit)
leg A
o-ring
leg B
oil plate
leg B
A) How to clean with nozzle pin
1. Turn off the stove valve and wait until the stove has completely
cooled down.
2. Remove the Jet by disassembling and removing the generator tube
assembly from the stove with the tool kit.
3. Clean the jet with the nozzle pin
pump knob
pipe bolt
Pump parts
pipe bushing
2255 Brunton Court, Riverton, WY USA 82501
ring
PH: 307.857.4700
guide spring
guide
4. Re-Assemble the stove and check for any fuel leaks.
wave washer
venturi
guide spring
guide
nozzle
Warranty card must be filled out completely and returned within 30 days with proof of purchase for warranty to be valid.
pump knob
hose cap
LIMITS OF LIABILITY
filter
nozzle
packing washer
heating pipe
nozzle
connect bolt
BRUNTON
body nut
heating pipe
bolt
ATTN: WARRANTY DEPT.
2255 BRUNTON COURT
RIVERTON, WYOMING 82501
307.857.4700
nozzle
nozzle
connect nut
guide washer
packing holder
packing rubber
hose
o-rings
connect
Brunton assumes no responsibility for any inconvenience, loss, or injury, direct or
consequential damage arising from possession or use of the goods. This warranty gives
you specific legal rights which may vary from state to state. Check with your local state
about your rights.
washer
nozzle body
- If cleaning the Jet does not improve the stove efficiency, clean the generator tube as well.
B) How to clean the generator tube
setting bushing
1. Begin by removing the generator tube assembly from the stove with
the tool kit.
2. Pull the wire out brush clean of any debris and replace
3 . Re-Assemble the stove and check for any fuel leaks
hose
valve
connect
connect bushing
spindle
pipe bolt
pipe bushing
BRUNTON WARRANTY REGISTRATION
head assembly
setting bolt
NAME_______________________________________________________
ADDRESS___________________________________________________
CITY_________________________ST/PROV_______ZIP__________
PHONE _______________________EMAIL_______________________
MODEL#__________________DATE PURCHASED____________
PURCHASED FROM_______________________________________
CITY_________________________ST/PROV_______ZIP__________
valve connect bolt
housing cap
nylon hose
housing
knob
o-rings
pipe
WARNING
o-rings
filter
air bushing body
o-ring
WARNING
Only use in well ventilated areas.
Keep well away from children.
PRICE PAID $___________________
1006
Do not leave unattended while in use. Do not operate near flammable materials.
air bushing
After disassembling and assembling, be sure to check for leakage with soapy water.
air bolt
air spring
|
Bissell Vacuum Cleaner 17G5 User Manual
Black Decker Trimmer 243257 01 User Manual
Blodgett Convection Oven SHO E User Manual
Blue Rhino Outdoor Fireplace 255635 User Manual
Bowers Wilkins Speaker ASW675 User Manual
Braun Thermometer IRT4520 User Manual
Breville Rice Cooker BRC520 User Manual
Candy Washer CE 104 1 User Manual
Carrier Air Conditioner 19XRV User Manual
Casio Electronic Keyboard CTK 591 User Manual