Washing Machine
Vaskemaskine
Пральна машина
Стиральная машина
WNF 6441 AE20
WNF 6461 AE20
WNF 6401 WE20
User‘s Manual
Brugsanvisning
Посібник користувача
Инструкция по эксплуатации
will switch to protection mode and will not
operate.
Appropriate installation location
•
Place the machine on a rigid floor. Do not
place it on a long pile rug or similar surfaces.
Total weight of the washing machine and the
dryer -with full load- when they are placed
on top of each other reaches to approx. 180
kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
Do not place the product on the power cable.
Do not install the product at places where
temperature may fall below 0ºC.
Do not use old or used water inlet hoses on
the new product. It may cause stains on your
laundry.
A
•
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
•
•
•
Place the product at least 1 cm away from the
edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Removing the transportation locks
Do not remove the transportation locks before
A
taking out the packaging reinforcement.
Remove the transportation safety bolts before
A
Ensure that the cold and hot water
operating the washing machine, otherwise, the
product will be damaged.
A
connections are made correctly when installing
the product. Otherwise, your laundry will come
out hot at the end of the washing process and
wear out.
1. Loosen all the bolts with a spanner until they
rotate freely (C).
2. Remove transportation safety bolts by turning
them gently.
2. Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel.
(P)
Keep the transportation safety bolts in a safe
C
place to reuse when the washing machine
needs to be moved again in the future.
3. Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
Never move the product without the
C
transportation safety bolts properly fixed in
place!
Connecting water supply
The water supply pressure required to run
C
the product is between 1 to 10 bars (0.1 – 10
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
Connecting to the drain
•
The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
If you are going to use the double water-inlet
C
Your house will be flooded if the hose comes
out of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of
the discharge hose tightly so that it cannot
come out.
A
product as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
If you want to use both water inlets of the
C
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
•
•
The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
In case the hose is elevated after laying it on
the floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
Models with a single water inlet should not be
connected to the hot water tap. In such a case
A
the laundry will get damaged or the product
3
EN
come out excessively wet. Therefore, follow
the heights described in the figure.
Do not use any tools to loosen the lock nuts.
Otherwise, they will get damaged.
A
Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the values in
the "Technical specifications" table. Our company
shall not be liable for any damages that will arise
when the product is used without grounding in
accordance with the local regulations.
•
To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do
not immerse the hose end into the dirty water
or drive it in the drain more than 15 cm. If it is
too long, cut it short.
The end of the hose should not be bent, it
should not be stepped on and the hose must
not be pinched between the drain and the
machine.
If the length of the hose is too short, use it
by adding an original extension hose. Length
of the hose may not be longer than 3.2 m.
To avoid water leak failures, the connection
between the extension hose and the drain
hose of the product must be fitted well with an
appropriate clamp as not to come off and leak.
•
•
•
Connection must comply with national
regulations.
•
•
Power cable plug must be within easy reach
after installation.
The voltage and allowed fuse or breaker
protection are specified in the “Technical
specifications” section. If the current value of
the fuse or breaker in the house is less than 16
Amps, have a qualified electrician install a 16
Amp fuse.
•
•
The specified voltage must be equal to your
mains voltage.
Do not make connections via extension cables
or multi-plugs.
Adjusting the feet
A
Damaged power cables must be replaced by
the Authorized Service Agents.
In order to ensure that the product operates
B
more silent and vibration-free, it must stand
level and balanced on its feet. Balance the
machine by adjusting the feet. Otherwise, the
product may move from its place and cause
crushing and vibration problems.
First use
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections "Important safety
instructions" and "Installation".
To prepare the product for washing laundry, perform
first operation in Drum Cleaning programme. If
your machine is not featured with Drum Cleaning
programme, use Cottons-90 programme and
select Additional Water or Extra Rinse auxiliary
functions as well. Before starting the programme,
put max. 100 g of powder anti-limescale into the
main wash detergent compartment (compartment
nr. II). If the anti-limescale is in tablet form, put only
one tablet into compartment nr. II. Dry the inside
of the bellow with a clean piece of cloth after the
programme has come to an end.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level
and balanced.
3. Tighten all lock nuts again by hand.
Use an anti-limescale suitable for the washing
C
machines.
Some water might have remained in the
product due to the quality control processes
C
4
EN
in the production. It is not harmful for the
Preparing laundry for washing
product.
•
Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons
will damage the machine. Remove the metal
pieces or wash the clothes by putting them in a
laundry bag or pillow case.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place away
from reach of the children.
Packaging materials of the product are
manufactured from recyclable materials. Dispose of
them properly and sort in accordance with recycled
waste instructions. Do not dispose of them with
normal domestic waste.
•
•
Take out all substances in the pockets such as
coins, pens and paper clips, and turn pockets
inside out and brush. Such objects may
damage the product or cause noise problem.
Put small size clothes such as infant's socks
and nylon stockings in a laundry bag or pillow
case.
Transportation of the product
Unplug the product before transporting it. Remove
water drain and water supply connections. Drain
the remaining water in the product completely;
see, "Draining remaining water and cleaning the
pump filter". Install transportation safety bolts
in the reverse order of removal procedure; see,
"Removing the transportation locks".
•
•
•
Place curtains in without compressing them.
Remove curtain attachment items.
Fasten zippers, sew loose buttons and mend
rips and tears.
Wash “machine washable” or “hand washable”
labeled products only with an appropriate
programme.
Never move the product without the
C
•
Do not wash colours and whites together. New,
dark coloured cottons release a lot of dye.
Wash them separately.
transportation safety bolts properly fixed in
place!
Disposing of the old product
Dispose of the old product in an environmentally
friendly manner.
Refer to your local dealer or solid waste collection
centre in your area to learn how to dispose of your
product.
For children's safety, cut the power cable and break
the locking mechanism of the loading door so
that it will be nonfunctional before disposing of the
product.
•
•
Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.
Use only dyes/colour changers and limescale
removers suitable for machine wash. Always
follow the instructions on the package.
Wash trousers and delicate laundry turned
inside out.
•
•
Keep laundry items made of Angora wool in
the freezer for a few hours before washing. This
will reduce pilling.
Laundry that are subjected to materials such
as flour, lime dust, milk powder, etc. intensely
must be shaken off before placing into the
machine. Such dusts and powders on the
laundry may build up on the inner parts of the
machine in time and can cause damage.
•
3 Preparation
Things to be done for energy saving
Following information will help you use the product
in an ecological and energy-efficient manner.
•
Operate the product in the highest capacity
allowed by the programme you have selected,
but do not overload; see, "Programme and
consumption table".
Correct load capacity
The maximum load capacity depends on the type
of laundry, the degree of soiling and the washing
programme desired.
•
•
•
•
•
Always follow the instructions on the detergent
packaging.
The machine automatically adjusts the amount of
water according to the weight of the loaded laundry.
Wash slightly soiled laundry at low
temperatures.
Follow the information in the “Programme
A
Use faster programmes for small quantities of
lightly soiled laundry.
and consumption table”. When overloaded,
machine's washing performance will drop.
Moreover, noise and vibration problems may
occur.
Do not use prewash and high temperatures for
laundry that is not heavily soiled or stained.
If you plan to dry your laundry in a dryer, select
the highest spin speed recommended during
washing process.
Loading the laundry
•
•
•
Open the loading door.
Place laundry items loosely into the machine.
Push the loading door to close until you hear a
locking sound. Ensure that no items are caught
in the door.
•
Do not use detergent in excess of the amount
recommended on the detergent package.
Sorting the laundry
•
Sort laundry according to type of fabric, colour,
and degree of soiling and allowable water
temperature.
The loading door is locked while a programme
is running. The door can only be opened a
while after the programme comes to an end.
In case of misplacing the laundry, noise and
vibration problems may occur in the machine.
C
•
Always obey the instructions given on the
garment tags.
A
5
EN
•
Do not use amounts exceeding the dosage
quantities recommended on the detergent
package to avoid problems of excessive
foam, poor rinsing, financial savings and finally,
environmental protection.
Using detergent and softener
Detergent Drawer
The detergent drawer is composed of three
compartments:
- (I) for prewash
•
•
Use lesser detergent for small amounts or
lightly soiled clothes.
- (II) for main wash
– (III) for softener
Use concentrated detergents in the
recommended dosage.
– (*) in addition, there is siphon piece in the softener
compartment.
Using softeners
Pour the softener into the softener compartment of
the detergent drawer.
•
•
•
2
1
3
2
1
3
Use the dosages recommended on the
package.
Do not exceed the (>max<) level marking in the
softener compartment.
If the softener has lost its fluidity, dilute it with
water before putting it in the detergent drawer.
The detergent dispenser may be in two
different types according to the model of your
machine as seen above.
C
Using liquid detergents
If the product contains a liquid detergent cup:
•
•
•
•
Make sure that you have placed the liquid
detergent cup in compartment nr. "II".
Use the detergent manufacturer's measuring
cup and follow the instructions on the package.
Use the dosages recommended on the
package.
Detergent, softener and other cleaning
agents
•
•
•
Add detergent and softener before starting the
washing programme.
Never open the detergent drawer while the
washing programme is running!
If the liquid detergent has lost its fluidity, dilute it
with water before putting in the detergent cup.
When using a programme without prewash,
do not put any detergent into the prewash
compartment (compartment nr. I).
•
•
In a programme with prewash, do not put
liquid detergent into the prewash compartment
(compartment nr. I).
Do not select a programme with prewash if you
are using a detergent bag or dispensing ball.
Place the detergent bag or the dispensing ball
directly among the laundry in the machine.
If you are using liquid detergent, do not forget
to place the liquid detergent cup into the main
wash compartment (compartment nr. II).
If the product does not contain a liquid
detergent cup:
•
•
•
•
Do not use liquid detergent for the prewash in a
programme with prewash.
Use the detergent manufacturer's measuring
cup and follow the instructions on the package.
Liquid detergent stains your clothes when used
with Delayed Start function. If you are going
to use the Delayed Start function, do not use
liquid detergent.
Choosing the detergent type
The type of detergent to be used depends on the
type and colour of the fabric.
•
Use different detergents for coloured and white
laundry.
•
Wash your delicate clothes only with special
detergents (liquid detergent, wool shampoo,
etc.) used solely for delicate clothes.
When washing dark coloured clothes and
quilts, it is recommended to use liquid
detergent.
Using gel and tablet detergent
When using tablet, gel, etc. detergents, read
the manufacturer's instructions on the detergent
package carefully and follow the dosage values. If
there is not any instruction on the package, apply
the following.
•
•
Wash woolens with special detergent made
specifically for woolens.
•
If the gel detergent thickness is fluidal and
your machine does not contain a special liquid
detergent cup, put the gel detergent into the
main wash detergent compartment during first
water intake. If your machine contains a liquid
detergent cup, fill the detergent into this cup
before starting the programme.
Use only detergents manufactured specifically
for washing machines.
A
A
Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used
depends on the amount of laundry, the degree
of soiling and water hardness. Read the
manufacturer's instructions on the detergent
package carefully and follow the dosage values.
6
EN
•
•
If the gel detergent thickness is not fluidal or in
the shape of capsule liquid tablet, put it directly
into the drum before washing.
Put tablet detergents into the main wash
compartment (compartment nr. II) or directly
into the drum before washing.
Tablet detergents may leave residues in the
detergent compartment. If you encounter such
a case, place the tablet detergent between the
laundry, close to the lower part of the drum in
future washings.
C
Use the tablet or gel detergent without
selecting the prewash function.
C
Using starch
•
Add liquid starch, powder starch or the dyestuff
into the softener compartment as instructed on
the package.
•
•
Do not use softener and starch together in a
washing cycle.
Wipe the inside of the machine with a damp
and clean cloth after using starch.
Using bleaches
•
Select a programme with prewash and add
the bleaching agent at the beginning of the
prewash. Do not put detergent in the prewash
compartment. As an alternative application,
select a programme with extra rinse and add
the bleaching agent while the machine is taking
water from the detergent compartment during
first rinsing step.
•
•
Do not use bleaching agent and detergent by
mixing them.
Use just a little amount (approx. 50 ml) of
bleaching agent and rinse the clothes very
well as it causes skin irritation. Do not pour the
bleaching agent onto the clothes and do not
use it for coloured clothes.
•
•
When using oxygen based bleaches,
follow the instructions on the package and
select a programme that washes at a lower
temperature.
Oxygen based bleaches can be used together
with detergents; however, if its thickness is
not the same with the detergent, put the
detergent first into the compartment nr. "II"
in the detergent drawer and wait until the
detergent flows while the machine is taking in
water. Add the bleaching agent from the same
compartment while the machine is still taking in
water.
Using limescale remover
•
When required, use limescale removers
manufactured specifically for washing
machines only.
•
Always follow instructions on the package.
7
EN
Tips for efficient washing
Clothes
Light colours and
Delicates/
Woolens/Silks
Colors
Dark colors
whites
(Recommended
temperature range
based on soiling level:
40-90C)
(Recommended
(Recommended
(Recommended
temperature range based
on soiling level: cold-40C)
temperature range temperature range
based on soiling
level: cold-40C)
based on soiling
level: cold-30C)
It may be necessary
to pre-treat the
stains of perform
prewash. Powder
and liquid detergents
recommended
for whites can be
used at dosages
recommended for
heavily soiled clothes.
It is recommended to
use powder detergents
to clean clay and soil
stains and the stains
that are sensitive to
bleaches.
Powder and
liquid detergents
recommended for
Prefer liquid
Liquid detergents
suitable for
colours can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Use detergents without
bleach.
detergents
Heavily Soiled
produced for
delicate clothes.
Woollen and silk
clothes must
be washed with
special woollen
detergents.
colours and dark
colours can be
used at dosages
recommended
for heavily soiled
clothes.
(difficult stains
such as grass,
coffee, fruits and
blood.)
Prefer liquid
Powder and
Liquid detergents
suitable for
Powder and
detergents
liquid detergents
recommended for
colours can be used at
Normally Soiled
liquid detergents
recommended for
whites can be used at
dosages recommended
for normally soiled
clothes.
produced for
delicate clothes.
Woollen and silk
clothes must
be washed with
special woollen
detergents.
colours and dark
colours can be
(For example,
stains caused by
body on collars
and cuffs)
dosages recommended used at dosages
for normally soiled
recommended
clothes. Use detergents for normally soiled
without bleach.
clothes.
Prefer liquid
Powder and
Liquid detergents
suitable for
detergents
Powder and
liquid detergents
recommended for
colours can be used at
produced for
delicate clothes.
Woollen and silk
clothes must
be washed with
special woollen
detergents.
liquid detergents
recommended for
colours and dark
colours can be
Lightly Soiled
whites can be used at dosages recommended used at dosages
(No visible stains
exist.)
dosages recommended for lightly soiled clothes.
for lightly soiled clothes. Use detergents without
bleach.
recommended
for lightly soiled
clothes.
8
EN
4 Operating the product
Control panel
1
3
4
5
2
6
7
8
1
2
3
4
-
Spin Speed Adjustment button
Display
Temperature Adjustment button
Programme Selection knob
5
6
7
8
-
-
-
-
On / Off button
-
-
-
Delayed Start buttons (+ / -)
Auxiliary Function buttons
Start / Pause / Cancel button
Display symbols
Preparing the machine
Make sure that the hoses are connected tightly.
Plug in your machine. Turn the tap on completely.
Place the laundry in the machine. Add detergent
and fabric softener.
Programme selection
1. Select the programme suitable for the type,
quantity and soiling degree of the laundry
in accordance with the "Programme and
consumption table" and the temperature table
below.
F3
F2
F4
F1
Heavily soiled white cottons and linens.
(coffee table covers, tableclothes,
towels, bed sheets, etc.)
90˚C
Normally soiled, coloured, fade proof
cottons or synthetic clothes (shirt,
nightgown, pajamas, etc.) and lightly
soiled white linens (underwear, etc.)
a
b
c
d
e
-
-
-
-
-
Spin Speed indicator
Temperature indicator
Spin symbol
60˚C
Temperature symbol
Remaining Time and Delayed Start
indicator
40˚C- Blended laundry including delicate
30˚C- textile (veil curtains, etc.), synthetics and
f
-
Programme Indicator symbols (Prewash /
Main Wash / Rinse / Softener / Spin)
Economy symbol
Cold
woolens.
g
h
i
-
-
-
-
-
-
2. Select the desired programme with the
Delayed Start symbol
Door Locked symbol
Start symbol
Programme Selection button.
Programmes are limited with the highest spin
C
j
speed appropriate for that particular type of
k
l
Pause symbol
fabric.
Auxiliary Function symbols
No Water symbol
When selecting a programme, always consider
C
m
-
the type of fabric, colour, degree of soiling and
9
EN
permissible water temperature.
laundry with a very gentle washing action to not to
damage clothes.
Always select the lowest required temperature.
Higher temperature means higher power
consumption.
C
C
• Mini
Use this programme to wash your lightly soiled
cotton clothes in a short time.
For further programme details, see
"Programme and consumption table".
• Mini 14
Use this programme to wash your little amount of
lightly soiled cotton clothes in a short time.
• Darkcare
Main programmes
Depending on the type of fabric, use the following
main programmes.
Use this programme to wash your dark coloured
laundry or the laundry that you do not want it get
faded. Washing is performed with little mechanic
action and at low temperatures. It is recommended
to use liquid detergent or woolen shampoo for dark
coloured laundry.
• Cottons
Use this programme for your cotton laundry (such
as bed sheets, duvet and pillowcase sets, towels,
bathrobes, underwear, etc.). Your laundry will be
washed with vigorous washing action for a longer
washing cycle.
• Intensive
• Synthetics
You can wash your durable and heavily soiled
clothes on this program. In this program, your
clothes will be washed for a longer time and
an extra rinse cycle will be made compared to
the “Cottons” program. You can use it for your
heavily soiled clothes that you wish to be rinsed
gently.
Use this programme to wash your synthetic
clothes (shirts, blouses, synthetic/cotton blends,
etc.). It washes with a gentle action and has a
shorter washing cycle compared to the Cottons
programme.
For curtains and tulle, use the Synthetic 40˚C
programme with prewash and anti-creasing
functions selected. As their meshed texture causes
excessive foaming, wash the veils/tulle by putting
little amount of detergent into the main wash
compartment. Do not put detergent in the prewash
compartment.
• Lingerie
Use this programme to wash delicates such as
underwears. If there is little amount of laundry, use a
laundry net.
Enclasp and button the clothes, and zip up.
• Woollens
C
Washing is made at low temperatures and with
less mechanical movements.
Use this programme to wash your woolen clothes.
Select the appropriate temperature complying with
the tags of your clothes. Use appropriate detergents
for woolens.
Better rinsing results are obtained thanks to the
C
additional rinsing.
• Freshen Up
Additional programmes
For special cases, additional programmes are
available in the machine.
Use this programme to remove the odour on the
laundry that are worn only for once and do not
contain any stains or dirt.
Additional programmes may differ according to
C
|